Carpentry SWMS: Cheatsheet with 20 hazard & controls (Free PDF)
Covers site setup, wall and roof framing, formwork and structural fixing for residential and light commercial carpentry. No signup, no email required.
Hazards & controls
1. Falls from height while working on elevated frames or trusses
- ✓ Edge protection or guardrails installed before elevated work begins
- ✓ Harness and anchor point used for work above 2 metres
- ✓ EWP or scaffold used for truss installation, not ladders
- ✓ No work on unsecured or partially braced frames
2. Manual handling of timber, sheeting and pre-fabricated frames
- ✓ Team lifts for anything over 20kg or awkward loads
- ✓ Mechanical lifting (crane or forklift) for trusses and long lengths
- ✓ Correct manual handling technique briefed at toolbox talk
3. Nail gun and power tool injury
- ✓ Safety glasses and gloves worn for all fixing work
- ✓ Trigger lock engaged when tool is not in active use
- ✓ Only competent, briefed operators use powder-actuated or nail guns
4. Falling objects and struck-by incidents below elevated work
- ✓ Exclusion zone maintained below all elevated framing work
- ✓ Tools tethered or lanyarded when working at height
- ✓ Toe boards fitted to scaffold and elevated platforms
5. Table saw, circular saw and mitre saw kickback and blade contact injury
- ✓ Blade guards fitted and functional on all fixed and hand-held saws
- ✓ Push sticks and riving knife used for rip cuts
- ✓ Saw stopped and unplugged before blade changes or clearing jams
- ✓ Only competent, briefed operators use fixed power tools
6. Formwork collapse or blowout during concrete placement
- ✓ Formwork designed and braced to engineered specification before pour
- ✓ Props and bracing checked immediately before pour starts
- ✓ Exclusion zone maintained around formwork during pour
- ✓ No work permitted under unsupported or partially stripped formwork
Show all 20 hazards & controls
7. Collapse of partially erected or unbraced wall and roof frames
- ✓ Temporary bracing installed and maintained until permanent fixing is complete
- ✓ Frames not left unsecured overnight or ahead of forecast high wind
- ✓ Engineer sign-off obtained for any non-standard bracing arrangement
8. Falls through unprotected floor and stair voids
- ✓ Penetrations covered and clearly marked immediately after cutting
- ✓ Void covers rated for load and secured against displacement
- ✓ Edge protection maintained at stairwells until the balustrade is fixed
9. Falls from ladders during lining, fixing and fascia work
- ✓ Ladder rated and inspected before use
- ✓ Three points of contact maintained at all times
- ✓ Extension ladders secured top and bottom
- ✓ Step platform used instead of a ladder for repetitive short-duration tasks
10. Dust exposure from cutting treated pine, MDF and engineered timber products
- ✓ On-tool dust extraction used for saws and routers
- ✓ P2 respirator worn for extended or enclosed-space cutting
- ✓ Cutting done outdoors or in a ventilated area where practical
11. Struck by crane, truck or EWP during truss and frame delivery
- ✓ Exclusion zone maintained during crane lifts
- ✓ Spotter used for reversing delivery vehicles
- ✓ No work permitted under a suspended load
12. Noise exposure from saws, nail guns and routers
- ✓ Hearing protection worn for all high-noise tools
- ✓ Task rotation used to limit individual exposure duration
- ✓ Low-noise tool selection used where available
13. Eye and hand injury from nail gun discharge, offcuts and hand tools
- ✓ Safety glasses worn for all cutting and fixing work
- ✓ Cut-resistant gloves worn when handling rough or freshly cut timber
- ✓ Nail guns never carried or handed over with a finger on the trigger
14. Contact with asbestos in existing structures during renovation or alteration carpentry
- ✓ Suspect material identified and left undisturbed until tested
- ✓ Licensed asbestos removalist engaged if asbestos is confirmed
- ✓ Work stopped and area isolated if suspect material is found
15. Heat stress working outdoors during summer framing
- ✓ Hydration breaks scheduled during hot conditions
- ✓ Heavy framing work rescheduled to cooler parts of the day where practical
- ✓ Shade provided for breaks
16. UV exposure during extended outdoor framing and fixing work
- ✓ Sun-protective clothing and hat worn
- ✓ Sunscreen applied and reapplied through the day
- ✓ Shade used for breaks where available
17. Trip and slip hazards from offcuts, packaging and trailing leads
- ✓ Work area kept clear of offcuts and packaging throughout the day
- ✓ Cords and leads routed away from walkways
- ✓ Site cleaned up at the end of each shift
18. Hand-arm vibration from extended use of powered hand tools
- ✓ Tool use time limited and rotated between crew members
- ✓ Low-vibration tools selected where available
- ✓ Any tingling or numbness reported and reviewed
19. Working alone on isolated tasks such as fixing bearers or joists under a floor
- ✓ Check-in procedure maintained with the supervisor
- ✓ Mobile phone carried and charged at all times
- ✓ Lone work avoided for elevated-risk tasks
20. Wind loading on unsecured or partially fixed frames and trusses
- ✓ Work stopped in high wind conditions per manufacturer or engineer limits
- ✓ Additional temporary bracing added ahead of forecast wind events
- ✓ Loose sheeting and materials secured or stored before leaving site
Fill out a Safework SWMS in 5 mins with AI
Real Carpentry tasks, hazards and controls — auto-filled, not blank rows for you to research yourself.
Source: SafeWork SWMS (VIC)
- Fully editable by you
- Auto audits the risk assessment
- No more blank canvas syndrome
- Rapid fill & remember business info
Free download · No email required
Carpentry SWMS Cheatsheet
All 20 hazards & controls for formwork, framing and structural carpentry, laid out as a printable one-pager for your site file.
utedesk.com.au
Frequently asked questions
What is a SWMS?
A Safe Work Method Statement (SWMS) is a legally required document for high-risk construction work. It sets out the job steps, the hazards involved, and the controls you'll use to manage them before work starts.
Do I need a SWMS for formwork, framing and structural carpentry?
If the work falls into one of the 18 high-risk construction work categories under the WHS Regulations, a SWMS is mandatory before work can start. This template is pre-mapped to the categories that typically apply to carpentry work of this kind.
Is this template really free?
Yes. Join with your Google account in 10 seconds, no card required, and it's saved to your account ready to customise, publish and get signed by your crew online.
Can I use this template as-is?
Treat it as a starting point, not a finished document. Every site is different — add your site-specific hazards, confirm the controls suit the actual job, and have it reviewed before workers sign it.
This template is a starting point only. Review and adapt it for your actual site conditions before use — it is not a substitute for a competent person's own risk assessment.